How To Set Drag On Baitcaster

Download Article

Download Article

If you've been fishing for a while, you know how frustrating information technology is to lose a big fish to a cleaved line. This usually happens when the elevate, the device which sets how much resistance a fish feels when it pulls on the line, isn't set properly. Fortunately, in that location's an easy solution for adjusting the drag. Once you learn near your specific reel and elevate adjuster, check the resistance, and brand the necessary corrections. And so get out and catch the one that got abroad!

1. 

   1

   Determine what kind of reel you utilize. There are three basic types of reels that contain your line. This article won't become into the pros and cons of each; instead, it'due south important that you lot know what kind you have and where the drag adjustment is located.

   • Spincasting reels are closed face. Your line will exist encased past a cone-like cover and the line feeds out of a small hole in it.^[1]
   • Spinning reels are open up-faced. Your line spool will be exposed and you'll be able to watch information technology spin out. This one looks the most exposed.^[2]
   • Baitcasting reels look like a mix between an open- and closed-face reel. The most noticeable feature is that the whole line spool will turn when you bandage the line.^[three]

2. 

   2

   Locate your drag adjustment. Now that you know what kind of reel you lot're using, learn where the elevate aligning is located on your reel.

   • The spincast's drag aligning is usually next to the reel handle. It looks somewhat like a star-shaped knob and may click every bit you play with the drag. This allows yous to hear just how much yous're adjusting.
   • The spinning reel's drag adjustment is a circular knob facing out at the front end of your line spool.
   • The baitcaster'south elevate adjustment looks similar a star and is located next to the reel handle. Turning it clockwise will tighten it and counter-clockwise loosens the drag.

   Advertizing

3. 

   3

   Acquire the breaking forcefulness for your line. Look on the package your line came in. It should clearly state in pounds how much resistance your line can handle without breaking.

   • This will tell yous what your optimum elevate should be. Drag should always be no more than 25 pct of your your breaking force'due south resistance. To figure elevate, just divide your breaking force by 4. The result is what your drag should be gear up at.^[4]

4. 

   4

   Get a scale. Now that you know what your drag should be, y'all'll demand to meet where your elevate is currently set.

   • You can use a digital scale or a leap calibration (such as the sort used to weigh fish). Both take a claw at the end to which you attach your line.

Advertisement

1. 

   one

   Gather your rod. Set up your rod and thread the line equally though you are going to actually utilize the rod. Exist sure to thread the line through all of the guides in gild to become an accurate reading.

2. 

   2

   Tie your line to the scale. Yous'll demand to necktie it deeply to the hook at the finish of your digital or spring calibration. Make sure the line can't skid off when the scale is pulled.

3. 

   iii

   Position your rod. Hold the rod at a 45 caste angle. Information technology's useful to take a friend hold your rod or the scale. Keep the calibration vertical so that the hook and line are at the top.

4. 

   4

   Pull downward on the scale. At first, your line won't do anything other than curve down with the weight. Then, you should notice the elevate showtime to slip and the line extend. As before long equally this happens, look at the calibration and take a measurement.

5. 

   5

   Adjust your elevate. Await at where your drag is and what it should be set at. Apply the drag adjustment knob on your reel and tighten or loosen equally needed. Bank check the drag on a scale.

Advertisement

Add New Question

• Question

  What do I practice if my fishing line is all wrinkled?

  

  The line is wrinkled or loopy, it may exist considering the line has been sitting on the reel for a long time and should exist replaced. Newer line may be loopy when you lot outset employ it. To avoid loops in your reel, retrieve the line slowly while holding it firmly between your fingers until the line is tight. Once all the slack has been retrieved, permit go of the line and retrieve your lure/bait normally.

Ask a Question

200 characters left

Include your email accost to get a bulletin when this question is answered.

Submit

Advertisement

Video

• If you're using a leader, test the drag for whichever has a lower breaking force: your leader or your line.^[5]

Thanks for submitting a tip for review!

Advertisement

Well-nigh This Article

Article Summary X

Setting the drag properly on your angling reel will help yous keep your fish on the line without snapping it. To fix 1, outset, you'll need to get together your rod and thread the line. Tie the end of your line to a scale, then hold your rod at a 45-degree angle. Have a friend pull down on the scale slowly. In one case the drag starts to slip and the line extends, look at the calibration and take downwards the measurement. Then, use the drag adjustment knob to tighten or loosen it to what you lot need. In general, the drag should be no more than 25 percent of your breaking force's resistance. If you don't know this number, look on the packet your line came in, which should say how much resistance your line tin handle. To acquire how to locate your elevate adjustment knob, read on!

Did this summary help you lot?

Thank you to all authors for creating a page that has been read 66,409 times.

Did this commodity assist you?

Source: https://www.wikihow.com/Set-the-Drag-on-a-Fishing-Reel

Share this post